Shanghai air gun factory

● Before using this rifle please clean up all anticorrosion oil, with dry clean cloth. After using, the rifle should again wipe with dry clean cloth and put on gun oil in order to protect it from corrosion.
● Never use sundries such as steel needle, iron needle etc, as pellet o ruse low quality pellet to avoid damaging barrel of the rifle.
● Never compress the spring too long or shoot the rifle unloaded which will influence the function of the rifle spring and will damage the spare parts.
● Oiling with few drops of machine oil on the moving parts periodically on the air rifle to keep lubricate and air tight.
● All keep the safety on save positions, only when it is ready to shoot then pull the safety and shoot.
● Do not shoot at hard substance in short distance to avoid the pellet ricochet occure

	● Open up the collar in the front of barrel with your left thumb. Then pull down the operating arm with your other fingers.
(1)

	● Pull down the cocking lever until the trigger hanger pin is connected with the piston.
(2)

	● Hold the cooking lever with the left hand and insert a pellet into the chamber with the right hand and then draw the cooking lever back to its position.
(3)

	● Sight from the gap of the rear sight and make the front sight to be in the right middle of the gap then catch the target. Note that the correct way of thesight is to make up-side
(4)

(5)

of the gap and the top of the front sight and the down-side of the target even.

AIMING SYSTEM ADJUSTING:
● UP-DOWN ADJUSTING: Turn up-down adjusting screw right-handwise to lower the sight door when the hitting point is upper; turn up-down adjusting screw left-handed to heighten the sight door when the hitting point is lower.

LEFT-RIGHT ADJUSTING:
● Turn the left-right adjusting screw right-handwise to move the sight door rightwards when the hitting point is left-of-center; turn the left-right adjusting screw left-handed to move the sight door leftwards when the hitting point is left-of-center.
　　 About the adjustment method of the optic airming device, please read its application manual.

	● Hold the stock with right hand, push the button with left hand (gently pat the front barrel when using B1,B1-1 air rifle) and fold with left hand.
(1)

	● Hold the front part of the barrel with left hand,compress downward until the piston hook on the trigger.
(2)

	● Hold the barrel with left hand and insert a pellet into the chamber with right hand and then draw the barrel back to its position.
(3)

	● Sigth from the gap of the rear sight and mark the front sight to be in the right middle of the gap then catch the target. Note that the correct wat of the sight
(4)
is to make up-side of the gap and the top of the front sight and the downside of the target even. (Fig.4) If using optical sighting device please read the instruction of the optical sighting device

(5)

AIMING SYSTEM ADJUSTING:
● UP-DOWN ADJUSTING: Turn up-down adjusting screw right-handwise to lower the sight door when the hitting point is upper; turn up-down adjusting screw left-handed to heighten the sight door when the hitting point is lower.

LEFT-RIGHT ADJUSTING:
● Turn the left-right adjusting screw right-handwise to move the sight door rightwards when the hitting point is left-of-center; turn the left-right adjusting screw left-handed to move the sight door leftwards when the hitting point is left-of-center.
　　About the adjustment method of the optic airming device, please read its application manual.

The rifle which adopts CO₂ as its power will get a slow pellet initial velocity when the temperature is below 10℃ because CO₂ can only be used at the temperature between 10℃ to 38℃ ; When the temperature is more than 38℃ , pressure in the air tank will become so high that the hammer has no enough power to open the valve effectively and the fire function will be debased.

The initial velocity of the rifle is related to the temperature. It is very normal that different temperature can cause different velocity. CO₂ absorbs much heat when it is released, so you should not fire continuously. In order to assure the coherence of the initial velocity, every interval firing time should be more than 10 seconds.

The rifle should not approach to the heat source or be basked directly. If the rifle is heated excessively, then its seal components may be damaged.

The air cylinder should be stored without any air. The CO₂ air tank should be stored at the temperature below 60℃ .

Warning: When the temperature is over 71℃ , the CO₂ air tank has the possibility to explode.

Warning: The valve is forbidden to be discharged when the tank is full of gas; The cover of the cylinder is forbidden to be discharged when the cylinder is full of gas. The power of the parts dashing out is as strong as that of pellet.

Method of Loading: Load 12g CO₂ back into the tank and screw the cover. When it is tightly screwed, Screw the cover in the reverse direction, and you will feel some resistance. This shows that the cylinder is full of CO₂.

Way to Inflate: ① Screw the air feeding valve instead of the cover into the cylinder, and tightly twist the connected screw tap. ② Discharge the adapter from the inflation device, and twist it into the hole of the air feeding valve. ③ Connector the air taking valve with industrial CO₂ tank (using G5/8 inflation device) or with CO₂ extinguisher(using M22X1.5inflation device) ④ Insert the quick disconnect into the adapter. ⑤ Plug the air releasing key into the air releasing device and switch anti clockwise 180 degree to open the valve ⑥ Tightly twist the grip of the valve clockwise, and open the industrial air tank or control valve of the CO₂ extinguisher in a pulsed way. Then you can inflate and the gas in the air tank is released. (Warning: You have to inflate slowly otherwise the sealed components will be damaged.) ⑦ Twist the air releasing key in a reverse direction (180degree) and the valve is closed. Open the industrial air tank or the control valve of the CO₂ extinguisher slowly, and then inflate until the tank is full of 30g CO₂(30g CO₂ can be controlled in a weighting way.) ⑧ Release the grip of air taking valve in a reverse way and let the remaining air out. Discharge the quick disconnect and the whole process of inflation is finished. You can find the names of all spare parts at page 13.

We suggest that you use the inflation device with pressure gauge. During the process of the inflation. You may investigate the change of the pressure.

Warning: During the process of the inflation, the maximum air inflation must be less than 36g. If the air volume is over normality, you must reduce some by air releasing switch.

Way to connect the AR2079B with air tank AR2079Bis not equipped with air reservoir device, but it is supplied with standard G1/2 air tank connecting device, which can be connected with the tank from the paintball marker. Such as φ 50, 9 OZ CO₂ air tank (Made in USA). Twist the air tank into theadapter and you can use it.
Suggestion: If there is no necessity, please don't discharge the tank. The working life of the adapter, the screw and seal will be shorten If you charge or discharge the tank continually.

When changing the spare parts. Please contact us:
1. By call or by e-mail to local distributor
2. If you would like to want the damaged part to be done by an approved mechanist， Please contact our Department of Maintenance at 9F,zhongcheng Building,No.2159 South Pudong Road Pudong 200127,Shanghai,PR China
Tel:0086-21-50941989　50941990
Fax:0086-21-50941983

Not a toy. Used by ADULT only.
Never aim at anybody.
Never lean your rifle against walls and trees or any other object that cojld cause the rifle to fall after loading the pellet.
Always keep safety engaged until you are ready to shoot.